Welke beschermingsgraad haalt een DES-frame?

IP66 of NEMA 4X, met elke combinatie van doorvoerrubbers: enkel, dubbel, viervoudig of doorbreekbaar.

Kunnen kabels met connector erdoor?

Ja. Het frame is deelbaar, dus geconfectioneerde kabels worden erin gelegd in plaats van erdoor gestoken.

Hoe kies ik het juiste frame?

Op basis van het aantal en de diameters van je kabels. Stuur ons een kabellijst; wij stellen de combinatie van frame en doorvoerrubbers samen.

Wat is het verschil met een doorvoerplaat?

Een doorvoerplaat is een vaste plaat met membranen voor kabels zonder connector en is voordeliger. Een frame is deelbaar en geschikt voor kabels mét connector.

Cable entry frames.Dozens of cables, one neat opening.

A cable entry frame bundles all cables that have to enter a cabinet in one rectangular cut-out. It is split, so cables with a connector simply drop in. With cable grommets per cable the whole is sealed and every cable gets strain relief.

View the range Request advice

Black cable entry frame with various cables, including two thick black cables with connectors

Range

10 series in the range

Click on a series for all variants, article numbers and downloads.

DES 10

System

Very compact split frame for flexible and safe cable entry with a high degree of protection.

Cable Ø 2–35 mm · Also with connector

DES 16

System

Compact split frame for safe and flexible cable entry with a high protection rating.

Cable Ø 2–35 mm · Also with connector

Black cable entry frame with various cables, including a D-sub connector, through grey sealing modules

DES 24

System

Flexibly splittable frame for safe cable entry with a high degree of protection.

Cable Ø 2–35 mm · Also with connector

Black cable entry frame with various cables and connectors, fixed to a wall

DES 24 90

System

Split cable entry frame for right-angle (90°) cable entry in cabinets and panels.

Also with connector · 90° entry

DES L1

System

Elongated split frame for cables with connectors, with reliable strain relief and high IP protection.

Also with connector · IP66 · NEMA 4X

Black plastic cable entry frame with two cables, one grey and one black, passing through it

DES L2

System

Elongated split frame for compact cable entry with reliable sealing and strain relief.

Cable Ø 2–17 mm · Also with connector

DES L3

System

Elongated split frame for cable entry with high IP protection and strain relief.

Cable Ø 2–17 mm · Also with connector

Black cable entry frame with three cables, including a serial cable and two round cables

DES L4

System

Elongated split frame for larger cable entry with high IP protection and strain relief.

Cable Ø 2–17 mm · Also with connector

DES L5

System

Elongated split frame for maximum cable density with high IP protection and strain relief.

Cable Ø 2–17 mm · Also with connector

DES Q

System

Square split frame for safe cable entry in cabinets and machine panels with a high IP rating.

Also with connector · IP66 · NEMA 4X

About the product group · Detas Ultra

Cable entry frames

For: Cables with and without connector, Ø 2 to 35 mm
Protection: IP66 · NEMA 4X with any rubber combination
Fire behaviour: Fully self-extinguishing V0
Assembly: Split frame + freely positionable entry grommets

The frame consists of a split housing in which you place entry rubbers freely: single, double, quadruple or as a break-through blind rubber for later. After closing, the frame clamps the rubbers in place. This gives a seal against dust and water and strain relief on every cable at the same time.

The DES frames are available in compact, elongated and square versions and in a 90° version for right-angle entry. With any combination of grommets, IP66 / NEMA 4X is achieved; the system is fully self-extinguishing to V0.

When

When do you choose cable entry frames?

01Many cables in one place: Instead of a row of glands, a single cut-out. Faster to install and clearer for service.
02Cables with connectors: The frame is split: pre-assembled cables go in complete, with no cutting.
03Sealing matters: IP66 and strain relief in one, even with varying cable diameters.
04Expansion expected: Blind grommets keep space free for cables that are added later.

How to choose

From cable list to the right model

Send your cable list. We choose the model and size and check that everything fits.

Send your cable list

01Make a cable list
Number of cables, outer diameters and which have a connector. We use that to choose the entry grommets.
02Choose the frame size
Compact (DES 10), elongated (L series), square (Q) or large (16 and 24). The size follows from the number of grommets.
03Straight or right-angled
Do the cables need to run straight down along the cabinet wall? Then the DES 24-90 with angled entry.
04Keep space free
Plan one or two blanking grommets for future cables; that avoids a second cut-out later.

Application

Used in

Switch cabinets and control cabinets
Machine frames and operating panels
Robot cells and automation lines
Cabinets with many bus and sensor cables

What Wisman does for you

Advice on your cabinet: which entry, which size, how many cables
One point of contact from cable carrier to control cabinet wall
Datasheets and documentation per model available immediately
Matched to your cable package from the configurator or ChainLogic

Let the planner work it out

First enter your cable list. Cables without a plug go through an entry plate, cables with a plug get a split entry grommet. Would you rather route everything through one frame? We will put that layout together for you afterwards.

Open the cable entry planner

Frequently asked questions